South Carolina LP Gas Reseller Practice Test

These questions are part of the practice quiz. Start practicing

• What safety measure should be taken if there is a propane leak?
• What is the purpose of a fixed liquid level gauge on containers being filled by volume?
• What should you not do if you smell gas?
• What is the minimum height required for the industrial type fence enclosing bulk storage plants?
• The filling connections and vent from liquid gauges on DOT or ASME containers filled at permanent installation shall not be less than what distance from a source of ignition?
• What is the legal minimum distance from the point of transfer of LP Gas to the centerline of the nearest mainline railroad track?
• At what temperature does liquid propane vaporize?
• What is the primary responsibility of an LP gas reseller?
• What is required for an LP gas appliance to pass inspection?
• What does the term "propane vapor" refer to?
• What is the required ratio of Ethyl Mercaptan in LP Gas as measured per 10,000 gallons?
• What is the distance from a liquid transfer's shutoff valve that requires a hydrostatic relief valve?
• What are the signs of an LP gas leak?
• What does the color yellow signify in LP gas marking?
• Which safety practice is crucial when handling LP gas?
• In what scenario would the name of the LP Gas dealer be crucially important?
• Why is it important to secure LP gas tanks properly?
• How should a damaged propane tank be handled?
• What is the minimum distance the vent pipe of an LP Gas space heater should extend above the roof crest when installed within ten feet or less from the roof ridge?
• What is LP gas primarily made up of?
• What happens if propane is not stored upright?
• Which statement describes ideal ventilation for storing LP gas cylinders?
• How often should LP gas cylinders be inspected for safety and compliance?
• A cylinder marked with 4E-240 indicates what construction method and material?
• What is the maximum inside diameter allowed for transfer hoses used to fill individual containers indoors?
• What should be inspected regularly to ensure safe operation of an LP gas system?
• Which of the following is an acceptable method for testing LP Gas piping systems for leaks?
• Each individual plant with LP Gas storage containers shall have a fire extinguisher of what type?
• How should propane tanks be stored during extreme weather conditions?
• What is the maximum period allowed for a temporary installation according to NFPA #58?
• What feature is critical for an LP gas storage area?
• What safety measure must be observed regarding smoking and open flames near an ASME container?
• Which of the following is NOT allowed within a certain distance from an LP Gas container?
• What indicates that an LP gas truck is designed for propane delivery?
• What should be done if an LP gas leak is detected?
• What is the purpose of a gas leak detector?
• What should be done immediately if there is a gas leak detected?
• What is the maximum allowable capacity for residential LP gas tanks in South Carolina?
• Which agency's guidelines dictate the markings required when storing LP-Gas and other gases together?
• What is "odorant" in the context of LP gas?
• What device must be installed in a liquid transfer hose equipped with a shutoff valve at the discharge end?
• DOT specification containers shall be located and installed so that the discharge from the container pressure relief device is at least what distance below building openings?
• LP gas bulk storage tanks of 4,000 gallons or more must be supported by piers according to what guideline?
• According to NFPA pamphlet 58, why should all above ground LP Gas containers be kept properly painted with bright reflective paint?
• For safety, where must refueling of LP Gas forklifts be conducted?
• What is the legal minimum distance between the point of transfer of LP Gas and an outdoor public assembly area?
• What is a crucial design aspect of LP gas dispensers?
• What is the maximum quantity of LP Gas that may be stored inside a specifically constructed building or room?
• What is typically a risk if an LP Gas container is not painted with reflective paint?
• Which type of storage location is unsuitable for containers holding LP Gas fed to passenger vehicles?
• What is the safe distance to keep flammable materials from an LP gas cylinder?
• According to regulations, DOT containers must be designed and tested by which organization?
• What protocol should be followed in case of a propane-related fire?
• What is the purpose of a hydrostatic relief valve in a liquid transfer hose?
• Why is it essential to maintain certain distances between LP Gas valves and buildings?
• What is the minimum distance that must be maintained between the relief valve on a DOT container and a building opening beneath the level of the relief valve discharge?
• Propane gas is generally recognized by what type of smell?
• How is LP gas normally supplied to customers?
• What should be present on every LP gas truck that supplies propane?
• Who is responsible for ensuring that DOT cylinders and/or containers for LP Gas are requalified according to regulations?
• What is a critical factor for determining the proper size of LP gas piping?
• What is the maximum allowable distance for underground propane lines from buildings?
• How should LP gas cylinders be stored?
• Which of the following measurements corresponds to the maximum pressure discharge limit for liquid pumps?
• At what interval should the pressure relief valve on industrial trucks, including fork lift containers, be replaced?
• Where must industrial trucks with permanently mounted fuel tanks be refueled?
• What purpose does the safety pilot on an LP Gas appliance serve?
• What should be included in an emergency evacuation plan for an LP gas facility?
• What should be done if an LP gas appliance is found to be leaking?
• How often should propane tanks typically be inspected?
• What type of maintenance is essential for prolonging the lifespan of a propane tank?
• What is the role of an anode rod in LP gas water heaters?
• What material is commonly used for LP Gas containers to maximize safety and durability?
• What is the legal minimum distance required between the point of transfer of LP Gas and a building with fire-resistant walls?
• What is the maximum length allowed for a flexible component connector used in bulk plant piping systems?
• What is the purpose of the hydrostatic relief valve installed in the piping system of an LP Gas storage facility?
• What is the main purpose of a gas detection system in an LP gas installation?
• Which material is prohibited for use in container appurtenances for LP Gas under service conditions?
• Which method should be used to re-supply a permanent customer fuel storage facility located on a rooftop?
• Which federal agency is responsible for regulating the transportation of LP gas?
• What minimum working pressure should fittings used on the discharge of the liquid transfer pump be rated for?
• What is the maximum individual capacity for service station containers?
• What protective gear is commonly recommended when working with LP gas?
• Which organization provides guidelines stating that LP Gas containers must be painted with reflective paint?
• Which valve is designed to automatically close at the rated flow specified by the manufacturer?
• What is the primary function of a pressure relief valve in an LP gas system?
• What is the primary danger of LP gas in an enclosed space?
• What is a common sign of improper ventilation in LP gas systems?
• What is the main hazard when using improper testing methods on an LP Gas piping system?
• Hose conveying propane liquid and/or vapor at pressures greater than 5 PSIG should be designed for what minimum bursting pressure?
• What is the procedure for siphoning LP gas from a cylinder?
• What is the fire extinguisher rating required for LP Gas storage facilities?
• What is the maximum capacity of LP Gas permitted in a building undergoing minor renovations with public access during normal work hours?
• What is the role of a vapor recovery system during LP gas handling?
• What type of vent pipe should be installed on a LP Gas wall furnace exceeding 50,000 BTU?
• What is the recommended distance the regulator’s discharge must be from an opening in a building?
• Fittings used with vapor LP Gas at pressures not exceeding 125 PSIG should have a working pressure of what PSIG?
• When a dealer takes over another dealer's account, which action is not a legal requirement?
• What is the maximum number of capped openings allowed in ASME containers with a capacity of less than 2,000 water gallons?
• At what temperature does propane become a liquid?
• When using LP Gas for demonstration and/or training purposes, what is the distance required between multiple containers if each has a maximum water capacity of 5 pounds?
• Where should pressure gauges be installed in an LP Gas System used in a bulk plant?
• Why is an LP Gas dealer required to have his name permanently affixed to his tank at a consumer location?
• What is the maximum water capacity of an LP Gas fuel container that can be used on an individual forklift?
• What is the maximum recommended distance a propane tank should be placed away from a building?
• Before installing appliances in mobile homes and recreational vehicles, what kind of approval is necessary?
• What is the recommended action if the temperature of the LP gas tank drops significantly?
• What is the maximum LP Gas water capacity for a container that can be connected to any single manifold at a permanent installation on a roof using portable containers?
• How frequently should LP gas piping be inspected?
• Container appurtenances need to maintain what PSIG rated working pressure at a minimum?
• For LP Gas heaters used during construction, what is the safety check needed regarding the placement of heaters?
• Which type of heating system is specifically restricted from installation in bathrooms according to NFPA pamphlet #54?
• What could be a consequence of not having the LP Gas dealer's name on the tank?
• Which component is essential for ensuring safety during liquid transfer in LP Gas utilization?
• What is the primary function of a pressure relief valve in propane storage?
• What should you do to maintain safety when using multiple LP Gas containers in a public space?
• When should a regulator be checked for proper functioning?
• What must outdoor propane tanks be equipped with to ensure safety?
• What is the primary purpose of a relief valve in gas storage?
• If LP Gas heaters, other than integral heater-container units, are used in buildings under construction for temporary heating, what is the minimum distance the heaters should be located from the container?
• In case of an LP Gas leak within a building, what is the most critical action to take?
• What is the minimum rated working pressure that container appurtenances must have?
• Hoses used on the low pressure side of a regulator should not exceed what length when connecting to appliances?
• What is the importance of using a two-stage regulator for LP gas?
• What is an appropriate action to take if you suspect a propane leak?
• What is the minimum number of emergency access gates required for bulk storage plants protected by a six-foot high industrial fence?
• According to South Carolina's regulations, what is required to legally sell propane to the public?
• What does “ASME” stand for relating to propane tank specifications?
• What document should a licensed LP gas reseller have readily available?
• For LP Gas to be sold, what must a retailer be certified as?
• How does ensuring the vent pipe's height above the ridge crest enhance safety in LP Gas systems?
• What certification must an individual hold to sell propane in South Carolina?
• What is the purpose of using a pressure relief valve in LP gas systems?
• According to NFPA pamphlet #54, unvented space heaters should not be installed in which type of area?
• What must be done before performing maintenance on LP gas equipment?
• What is the main purpose of an LP gas Meter?
• What is the primary purpose of the liquid transfer pump in an LP Gas system?
• How often should LP gas cylinders be inspected for safety?
• Which of the following is a consideration when installing vent pipes on LP Gas wall heaters?
• What should be done with a propane tank that is no longer in service?
• What gas is primarily utilized as a heating fuel in residential areas?
• When storing LP-Gas and compressed gases in the same area, what must be marked according to NFPA #58?
• What is the term for the device that regulates the pressure of gas from the tank to the appliance?
• What is the primary function of the relief valve on a DOT container?
• What is a necessary requirement for servicing a vehicle powered by LP Gas inside a building?
• What must be ensured during the delivery of LP gas?
• What is the required distance for a discharge outlet of regulators vented to the outside from any building opening?
• How much time must pass from the date of manufacture for the periodic replacement of pressure relief valves in industrial trucks?
• What is the recommended method for thawing frozen LP gas lines?
• Which of the following is a sign of a possible LP gas leak?
• What is a key indicator of a propane tank's current content level?
• What is a common use of LP gas in residential settings?
• Who may be permitted to enter an LP Gas facility during business hours to ensure public safety?
• What type of odor is commonly associated with propane gas for safety?
• Which technique presents an unacceptable risk in checking an LP Gas piping system for leaks?
• What is the typical lifespan of a propane tank with proper care?
• What is the standard color used in LP gas lines to indicate propane?
• Which of the following is an essential safety precaution when handling LP gas?
• How is propane commonly transported to customers?
• What is the role of the Deputy State Fire Marshal in relation to LP Gas facilities?
• Which of the following is not a safety mechanism typically found in LP gas dispensers?
• The maximum discharge pressure of a liquid pump under normal operating conditions shall be limited to what pressure?
• What is the acceptable condition to transport propane cylinders in a vehicle?
• What is the maximum drill size opening allowed for the bypass in excess flow valves?
• What is one way to determine if a propane tank is full?
• Why is it crucial to properly train employees handling LP gas?
• What does "DOT" stand for in the context of LP gas cylinder regulation?
• LP Gas fuel containers used on passenger carrying vehicles shall not exceed what capacity?
• What is the minimum distance required between the relief valve on an ASME container of 125 water gallons capacity and a building opening below the discharge level?
• Under what conditions should LP gas cylinders be stored?
• What color is the propane gas commonly used for safety identification?
• What color-coded markings should be used for LP gas piping?
• Individual LP Gas containers used on other than passenger carrying vehicles that operate on highways shall not exceed what capacity?
• What does the "LP" in LP gas stand for?
• What is the main regulatory body overseeing LP gas in South Carolina?
• What is the maximum individual water capacity allowed for general use containers?
• What is the minimum storage distance of propane tanks from any structure?
• In residential applications, what is typically the main use of LP gas?
• In the event of a fire at a bulk storage plant, what is a recommended action to extinguish the fire?
• In buildings under construction or repair, what is the maximum total water capacity of LP Gas containers manifold together for any one heater?
• To which agency must all installations of LP Gas on roofs of buildings be reported?
• What is the minimum bursting pressure required for hose used for LP Gas liquid transfer?